Read--post 2

Project to determine the quilting

Goal number three on my June list was to determine the quilting for Read. I started stitching the center of the ribbon. Eventually, I stitched on each edge of the ribbon. I knew I wanted to do some dense quilting on the book and around "Read." 

Space divided; ghost strings quilted

I was stuck with what to do in the rest of the space. While I pondered, I stitched in the ditch around the strings at the top of the project. I was still stuck. When that happens, I divide the space. This time, I was stuck with how to do that! 

Gertie, my inner squirrel, and I had a conference. I thought, "What is already in the project that I can use as my guide?" My eyes lit upon the strings. I could divide the space into segments the size of the string blocks! Using a chalk pencil, I divided the space like that. 

I stepped back. I liked what I saw. I had some thoughts about what to put into the rectangles. Gertie chimed in with why not create ghost strings? Good idea, I replied. Gertie raced off doing her happy dance.

Filler stitches behind Read

I pulled a grey thread that was similar in color to the background and began stitching lines. I used the lines from the strings as my guide. Except, I matched the lines at the intersections because it lends better fluidity to the piece. It didn't take long to stitch the lines. I did use a ruler and ruler foot to quilt the lines.

Fillers used to quilt the book cover

After the lines, I stitched a couple filler stitch designs behind the word Read. A few pebbles within the word and some swirls in the background felt right. Then, I began quilting the book cover. I quilted pebbles down the spine. I used a darker gray cotton thread to quilt the floral motif. To make the design standout, I stitched over the lines three times. I switched thread to the lighter gray and quilted leaves in the background. I quilted a few pebbles in the space above the book as a fill. I quilted straight lines in the curved small sections at the top of the book to represent pages.

X's were a no go

I had considered hand stitching X's in the bottom four rectangles to represent the people that the character read to during the air raids. I didn't like how the X's looked so I switched to a simple running stitch. 

Back view of the hand stitching

I used one thread of black Aurifil 30wt thread that I doubled so I could begin the stitch without needing a knot. I popped the knot into the batting when I finished a line. I started with a no knot technique. I chalk marked some lines and I used masking tape to mark other lines. I still couldn't manage to stitch straight with either marking method!

Stitching the lines 

The hand stitched lines leave my mark as the maker. I decided the lines represent the text in a book.

The project waiting for facing

I hand washed the project in the sink to remove the glue basting. I blocked it. I was surprised at how wonky one side of the project was! 

The sleeve

After trimming the project, I added a facing. I had enough of the gray fabric to make the facing. I did make an inside mitered corner for the facing. 

Sleeve stitched in place

The sleeve was a fabric that arrived in my stash around the same time as the backing. I had considered using it as a neutral; but, decided it was too busy a print for that purpose.

The leftovers after adding the sleeve and facing

The little bit of gray leftover went into my Rainbow Scrap Challenge tub to use next month! I cut the leftover sleeve fabric into five inch squares.

Label

I added the label. Yes, I picked it up from the free table! Now I have another finish! I realized that this is number seven in my line series. I need to add that information to the label!

Thread used in project

I did give the project a final steam. The project measures 24 x 33 inches. 

View of the finished back

I used one and a half yards of fabric for this project. I have a net loss of 11 and half yards of stash this month!

View of the finished front

Linking to: Oh Scrap, Sew & Tell, I Quilted This and Finished or Not Friday.